![]() If anyone has advice on anything I've said let me know. I'll update when I have some more work done. Any info on that would be great before I drill into this one. I still haven't found anything on the latching hood not having a hole for the pin in it which was the main reason for my last post. I have also cleaned up all the cut pieces so they are as flat and smooth as possible. The bolt can move up and down quite a bit with these pieces. I have not contacted Ben Edward's about it as I got these pieces today but I think you can see the issue it may cause. Not a problem for the straight repair piece but for the repair piece that goes around the trunnion it will be. ![]() Only problem I see is the height of the repair sections are different from the stock metal(see pictures). Great quality and with the two pieces I got I can replace anything behind the barrel I need. We already agreed the cutting torch guy is a dick and I decided too much metal was missing so I got some Ben Edward's Design repair sections. Some things are because of the tolerances of the gun but a lot of it is not. The tang cutout in the stock was way too small. Stock was not fully milled out where the receiver lays(you can see the lighter color in the pictures, those are the places I had to adjust). I had to do a LOT of work to this stock to be even close to correct. Looks great! I should've actually played around with the stock and receiver before I stained it. It comes cut to hell and with a virgin stock that is hard to tell if it is actually wood or not. We discussed two commands that you can use to fix the error: the git pull origin and git pull -rebase origin commands.Recap: This is an AoA kit. This error occurs when you attempt to push your local changes to the remote repo without updating your local repo with new changes made to the remote repo. In this article, we talked about the error: failed to push some refs to error. The second command pushes your local repo's current state to the remote branch. If the first command above runs successfully, you should get a response that says: Successfully rebased and updated refs/heads/main. To fix the error, go on and run following commands: git pull -rebase origin main The git pull -rebase command is helpful in situations where your local branch is a commit behind the remote branch. How to Fix error: failed to push some refs to Error in Git Using git pull -rebase In that case, use the solution in the next section. If the error persists, you'll get an error that says: fatal: refusing to merge unrelated histories. If the request succeeds, then go on and run the command below to push your own changes: git push -u origin main Just keep in mind that there are chances of failure when using this command to sync your remote and local repos to get rid of the error. If you're working with a different branch, then you'd have to replace main in the example above with the name of your branch. Here's how you can do that: git pull origin main In our case, we're trying to get rid of the error: failed to push some refs to error by sending a pull request. Once the merging is done, you can then push your own code changes to GitHub. To send a pull request means to "fetch" new changes made to the remote repo and merge them with the local repo. ![]() How to Fix error: failed to push some refs to Error in Git Using git pull Let's go over how you can use the commands above. In most cases, the latter fixes the error. We can fix the error: failed to push some refs to error in Git using the git pull origin or git pull -rebase origin commands. To register the updated R version with RStudio, you can do it from Tools > Global options. To update RStudio, go to the Check for updates option under Help menu. How to Fix the error: failed to push some refs to Error in Git 3.5.3 and 3.4.3 are versions of R, and not of RStudio. We'll be discussing two possible ways of fixing this error in the sections that follow. This is necessary so that you don't override the changes made by others. So Git is trying to tell you to update the local repo with the current changes in the remote before pushing your own changes. This error mainly occurs when you attempt to push your local changes to GitHub while the local repository (repo) has not yet been updated with any changes made in the remote repo. When collaborating with other developers using Git, you might encounter the error: failed to push some refs to error. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |